                                                           File: PATEXAM1.TXT


                    PATRIOT Model System Example 1

            Center for Exposure Assessment Modeling (CEAM)
            U.S. Environmental Protection Agency (U.S. EPA)
               Office of Research and Development (ORD)
            Athens Environmental Research Laboratory (AERL)
                       960 College Station Road
                      Athens, Georgia 30605-2700

                             706/546-3549



-----------------------------------------------------------------------------

NOTE:  The key strokes and commands listed in this example coincide with and
can be automatically executed from within the PATRIOT program with the
interactive log file PATEXAM1.LOG, or they can be executed interactively by
the user by following the sequence listed below.  Refer to the file READ.ME
for further information.


Introduction
~~~~~~~~~~~~
This example is based on first selecting a specific area of the country
(e.g., Clarke County, GA) then analyzing a set of soils (i.e., those that
support Corn) within that area.  The pesticide used is Aldicarb and the crop
is corn.  After performing a standard run comparing 10 scenarios, the
scenario with the highest leaching is used to demonstrate uncertainty
analysis.

Key Stroke/Command Sequence
~~~~~~~~~~~~~~~~~~~~~~~~~~~
a         Select Analyze
g         Select Geographic
d         Select Define
d         Select Database
x         Press any key to toggle on State/County coverage (x was
          used to show up in log file)
F2        Press F2 to Accept
a         Select Add
gaclar    Type enough of Clarke county Georgia to be unique
F2        Press F2 to Accept and add Clarke county as an area to
          search
F4        Press F4 to Previous out of Add screen
ret       Select RETurn
f         Select Find
F2        Press F2 when done viewing search results (13 soils
          found)
m         Select Map
F2        Press F2 to Accept defaults
<CR>      Press Carriage Return (Enter) when done viewing map
r         Select Return
s         Select Soils
d         Select Define
p         Select Property
s         Select Select
<CR>      Press Carriage Return (Enter) twice to move
<CR>      to the Ag Only option field
x         Press any key to toggle on Ag only
<CR>      Press Carriage Return (Enter) twice to move
<CR>      to the Crop data field
1         Enter crop number 1 for Corn
F2        Press F2 to Accept specifying Corn as search criteria
r         Select Return
f         Select Find
F2        Press F2 when done viewing search results (should find 10
          of 13 soils in buffer)
o         Select Order
a         Select Area
F2        Press F2 to Accept defaults for Sort (Descending)
r         Select Return
i         Select Infiltration
s         Select Summarize
F2        Press F2 to send summary to the screen
F2        Press F2 when done viewing summary
v         Select View
F2        Press F2 to Accept the default station (Athens)
F2        Press F2 to Accept defaults for time-series plot
<CR>      Press Carriage Return (Enter) when done viewing plot
v         Select View
F2        Press F2 to Accept the default station
<CR>      Press Carriage Return (Enter) twice to move to the
<CR>      Time Step data field
y         Enter y to generate a yearly time-series plot
F2        Press F2 to Accept
<CR>      Press Carriage Return (Enter) when done viewing plot
r         Select Return
p         Select Pesticide
n         Select Name
ald       Enter enough of Aldicarb to get a unique match
F2        Press F2 to Accept
s         Select Summary
F2        Press F2 to send summary to screen
F2        Press F2 when done viewing summary
r         Select Return
c         Select Cropping
d         Select Define
corn      Enter Corn as the crop of interest
F2        Press F2 to Accept
f         Select Find
s         Select Summary
F2        Press F2 to send summary to screen
F2        Press F2 when done viewing summary
r         Select Return
w         Select Worksheet
F2        Press F2 to Accept worksheet defaults
F2        Press F2 when done viewing Worksheet message
r         Select Return
i         Select Input
t         Select Type
x         Press any key to toggle on Standard type run
<CR>      Press Carriage Return (Enter) twice to move to the
<CR>      Starting Year data field
1964      Enter starting date
<CR>      Press Carriage Return (Enter) to move to Ending Year
          field
1964      Enter ending date
F2        Press F2 to Accept input
s         Select Soil
F2        Press F2 any number of times to page through the soils
F2        being used in the scenarios
F6        Press F6 to interrupt paging through soils (or use F2
          enough times to page through all ten soils)
i         Select Infiltration
F2        Press F2 to Accept
p         Select Pesticide
F2        Press F2 to Accept
c         Select Crop
F2        Press F2 to Accept
d         Select Depth
F2        Press F2 to Accept
o         Select Overview
F2        Press F2 to output overview to screen
F2        Press F2 any number of times to page through the
F2        Scenario Overviews
F6        Press F6 to interrupt paging through Overviews (or use F2
          enough times to page through all ten soils)
r         Select Return
e         Select Estimate
e         Select Execute
u         Select Unit
F2        Press F2 to Accept defaults
<CR>      Press Carriage Return (Enter) when done viewing plot
w         Select Weighted
F2        Press F2 to Accept defaults
<CR>      Press Carriage Return (Enter) when done viewing plot
r         Select Return
i         Select Input
t         Select Type
<CR>      Press Carriage Return (Enter) to move to the Monte Carlo
          field
x         Press any key to toggle on Monte Carlo type run
<CR>      Press Carriage Return (Enter) to move to Scenario number
          field
3         Enter scenario 3, as it had the highest leaching results
<CR>      Press Carriage Return (Enter) to move to number of runs
          field
20        Enter 20 to minimize length of run
F2        Press F2 to Accept values
m         Select Monte
<CR>      Press Carriage Return (Enter)
<CR>      3 times to move to
<CR>      the Decay Rate field
x         Press any key to toggle on Decay Rate as MC parameter
<CR>      Press Carriage Return (Enter) to move to Layer field
sur       Enter sur to select decay in the surface layer only
F2        Press F2 to Accept values
<CR>      Press Carriage Return (Enter) to move to Standard
          Deviation field
.01       Enter standard deviation value
<CR>      Press Carriage Return (Enter) twice to move to
<CR>      the Maximum Value field
.05       Enter maximum value
F2        Press F2 to Accept values
r         Select Return
e         Select Estimate
e         Select Execute
m         Select Monte
F2        Press F2 to Accept defaults for plot
<CR>      Press Carriage Return (Enter) when done viewing plot
r         Select Return
r         Select Return
